This article contains affiliate links: we may earn a small commission at no extra cost to you.

The most common question in every resin printing forum, asked roughly once a day forever, is some version of “can I just use a nail lamp?” The answer is yes, and most of the people telling you otherwise are trying to sell you a station. But there are three or four ways to get it wrong with a cheap lamp, and they are the difference between a mini that hardens properly and one that stays tacky, yellows, or snaps at the ankles the first time it hits a table. If you are still sorting out the supply side of resin printing generally, best resin for 3D printing miniatures is the place to start, because the resin you pick changes how long you cure more than the lamp does.

I print on an Elegoo Saturn, and my curing setup has been through the whole progression: nail lamp in a cardboard box, then a proper station, then a station plus a turntable because I got tired of rotating minis by hand. This is what I learned about which part of that spending was actually necessary.


The Short Answer

If you print occasionally, buy a 405nm UV nail lamp for around $20 and a $12 motorized turntable. That combination cures 28mm miniatures correctly and costs less than a single bottle of resin.

If you print weekly, buy a wash and cure station instead. Not because the curing is dramatically better, but because doing the wash step by hand in an open jar of IPA is the part that actually wears you down. The cure function comes along for the ride.

If you are printing terrain, large monsters, or full build plates at a time, you need a chamber with real coverage, which means either a large station or a DIY array. Nail lamps do not have the physical volume for it.


What a Cure Lamp Actually Needs to Do

Three things matter, and only three.

Wavelength. MSLA resin is formulated to cure at 405nm. That is the same wavelength your printer’s LCD array uses. A lamp that outputs 405nm cures your prints. A lamp that outputs only 365nm (some older or specialty nail lamps, most “blacklight” bulbs) will cure resin, but slower and less completely, because you are off the resin photoinitiator’s peak absorption. Most modern UV nail lamps are dual-wavelength and list both 365nm and 405nm on the box. That is what you want. If a listing does not state the wavelength at all, assume it is a gamble and buy a different one.

Coverage. This is where cheap lamps genuinely fall down, and it is not a wattage problem. A nail lamp is designed to point light down at a flat hand. A miniature is a three-dimensional object with undercuts, a cloak, and an armpit. Light that never reaches the underside of a cape does not cure the underside of a cape. Coverage is solved with reflection and rotation, not by buying a more powerful lamp.

Time under light. More is not better past a point. Over-curing is real: resin that spends far too long under UV gets brittle and, in clear or light resins, visibly yellows. A 28mm mini in a decent nail lamp is usually done in two to four minutes total across rotations. Fifteen minutes “to be safe” is how you make a mini that snaps at the ankle.

Notice that wattage is not on that list. A 48W nail lamp mostly means it finishes faster than a 24W one, not that it cures better. Buying up on wattage alone is the most common wasted upgrade in this whole category.


The Options, Ranked

Budget Start: A 405nm UV Nail Lamp

This is the honest beginner answer and I will not pretend otherwise. A UV nail lamp in the 24W to 48W range runs $18 to $30, cures miniatures properly, and is genuinely all you need for the first few months.

The catch is that the lamp alone is half the setup. Nail lamps light from above and from the sides of a shallow arch. Set a mini on the bare plastic base and the bottom third of it sits in shadow. Two fixes, both cheap: put the mini on a small mirror or a square of aluminum foil to bounce light back up underneath, and rotate it partway through the cure.

What is good:

What is not ideal:

Approximate cost: $18 to $30 (Amazon).

Best for: Anyone in their first six months of printing, and anyone printing occasionally forever.


The Fix That Makes a Nail Lamp Work: A Motorized Turntable

Pairing the lamp with a solar or battery motorized display turntable is the single highest-value $12 in this entire article. It rotates the mini continuously under the lamp, which solves the coverage problem that everyone blames the lamp for.

Get one small enough to fit inside the lamp’s arch, which usually means a 4 inch or smaller platter. Battery-powered is more reliable here than solar, because the inside of a UV lamp is not actually bright in the visible spectrum that solar cells want.

Approximate cost: $10 to $18 (Amazon).


The Upgrade: A Wash and Cure Station

A station is the point where you stop thinking about curing as a task. Elegoo’s Mercury line and Anycubic’s Wash and Cure both put a 405nm array, a reflective chamber, a turntable, and a timer into one box, and they handle the IPA wash step in the same unit.

The honest framing: you are not buying better curing. A nail lamp with a turntable and a foil reflector cures a 28mm mini about as completely as a station does. You are buying the wash half, plus never thinking about coverage again. If you are printing every week, that is worth $50. If you print twice a year, it is not.

I went into which specific station to buy in the best wash and cure station roundup, and if you have narrowed it to the top contenders, the Mercury Plus vs CW3 vs Anycubic head-to-head goes deeper.

What is good:

What is not ideal:

Approximate cost: $45 to $75 (Amazon, or direct from Elegoo and Anycubic).

Best for: Weekly printers, and anyone who has decided they are staying in the hobby.


Standalone UV Cure Chambers

A middle option that gets overlooked: a cure-only chamber with no wash function. These are essentially a reflective box with a 405nm array on multiple walls and a turntable, in the $40 to $80 range.

They make sense in exactly two situations. First, if you are running water-washable resin and genuinely do not need an IPA wash chamber, a wash function you will never use is wasted money. Second, if you already own a station and want a second, larger cure box for terrain, this is cheaper than a second full station.

Approximate cost: $40 to $80 (Amazon).

Best for: Water-washable printers, and terrain printers who need volume more than they need a wash basin.


The DIY Array

A strip of 405nm UV LEDs, a 12V power supply, and any box you line with foil will out-cure most commercial options for about $25 in parts, because you control the coverage completely. Wrap the strip around the interior walls in a spiral rather than running it along one side, drop a turntable in the middle, and you have a chamber with genuinely even exposure.

Two warnings. Buy 405nm specifically, not a generic “UV” or “blacklight” strip, which is usually 395nm or worse and marketed vaguely on purpose. And build the box so it fully closes, because the entire point of a reflective enclosure is defeated by an open side, and because you should not be looking at a running UV array anyway.

This is the right call if you print terrain or large models and the commercial chambers are all too small. It is the wrong call if you want to spend your hobby time painting rather than wiring.

Approximate cost: $20 to $35 in parts (Amazon).

Best for: Terrain and large-format printers, and anyone who enjoys the build as much as the print.


The One That Is Not a Cure Lamp: UV Flashlights

A 395nm or 405nm UV flashlight is a useful tool and a terrible primary cure source. It has no coverage, no timer, and no consistency, and holding one over a mini for four minutes is not a life.

What it is genuinely good for: spot-curing a repair, hardening a blob of resin used as glue, checking whether a surface is still tacky, and curing the resin residue in your waste IPA before disposal. Every resin printer should own one. None of them should cure minis with it. It shows up on the resin printer accessories list for exactly those reasons.

Approximate cost: $10 to $20 (Amazon).


Comparison Table

OptionWavelengthCoverageApprox. CostBest For
UV nail lamp + turntable365nm / 405nmGood with rotation$30 to $45 totalThe correct beginner answer
Wash and cure station405nmExcellent$45 to $75Weekly printers
Standalone cure chamber405nmExcellent$40 to $80Water-washable, terrain volume
DIY LED array405nm (buy specifically)Best, you control it$20 to $35Large models, tinkerers
UV flashlight395nm / 405nmNone$10 to $20Spot repairs, waste IPA, never minis

Cure Times That Do Not Wreck the Mini

Times vary by resin, lamp power, and print thickness, so treat these as starting points and adjust from what you see:

The test for “done” is touch, not the clock. A properly cured mini is dry and hard with no tackiness anywhere, including inside recesses and under overhangs. If any surface is still slightly sticky, it needs more time or it needs the light to actually reach that surface, and those are two different problems with two different fixes.

The failure mode on the other end is quieter and worth naming: an over-cured mini looks fine, primes fine, and then breaks at a thin ankle or a spear shaft under normal handling. If your minis keep snapping in the same places, look at cure time before you blame the resin. The full workflow is covered in how to cure resin miniatures, including the wash-and-dry sequence that has to happen first.


Do Not Cure Wet, and Do Not Cure in the Sun

Two shortcuts that cost people prints.

Curing a print that is still wet with IPA gives you a cloudy, chalky surface finish that no amount of priming fully hides. Wash, then let it air dry for five to ten minutes, then cure. The dry step is not optional and it is the one people skip.

Sunlight does cure resin, and it is free, and it is genuinely how a lot of people started. It is also uncontrolled: exposure varies by time of day and season, you cannot time it, and a mini left on a windowsill all afternoon is an over-cured mini. Use sunlight for curing waste resin and dirty IPA, where over-curing is the goal. Use a lamp for things you painted.


Safety, Briefly and Seriously

405nm UV is not sunlight, but it is not harmless either. Do not look directly at a running array, do not cure with an open chamber pointed at your face, and do not let kids treat a nail lamp like a toy. Cheap open-arch nail lamps are the worst offender here specifically because there is nothing blocking the light from your eyes. Curing inside a closed box, even a cardboard one, fixes it.

The broader chemistry side of this hobby, gloves, ventilation, and how to dispose of contaminated IPA, is covered in the resin printing safety guide. If you are new to the whole workflow, the complete beginner’s guide to resin miniature printing puts curing in context with everything before it.


What I Would Actually Buy

Starting today with nothing: a 48W dual-wavelength nail lamp and a small battery turntable, about $35 together, set inside a cardboard box lined with foil. That setup cures 28mm minis correctly and I would not feel undergunned using it indefinitely.

Printing weekly and tired of the IPA jar: skip straight to a wash and cure station. You are buying the wash, and the curing is a bonus you stop thinking about.

Printing terrain or anything that does not fit in a 6 inch chamber: build the DIY array. Nothing commercial in the hobbyist price range gives you both the volume and the coverage, and the parts cost less than the smallest station.


Frequently Asked Questions

Can I really use a nail lamp to cure resin miniatures? Yes. Buy one that lists 405nm output, add rotation and a reflective surface underneath, and it cures 28mm minis completely. The reason people say it does not work is almost always a coverage problem, not a lamp problem: they set the mini on the flat plastic base, cured one side, and found the underside tacky.

What wavelength do I need, 365nm or 405nm? 405nm. That matches the photoinitiators in standard MSLA resin and the wavelength your printer already uses. Most nail lamps are dual 365nm and 405nm, which is fine, the 405nm portion is doing the work. Avoid anything that only specifies 365nm, and avoid generic “blacklight” bulbs entirely.

Does higher wattage cure better? It cures faster, not better. A 48W lamp finishes in less time than a 24W lamp, but a fully cured mini is fully cured either way. Spend the money on rotation and coverage before you spend it on wattage.

Do I still need to cure water-washable resin? Yes, and this trips people up constantly. Water-washable refers to the cleaning step, not the curing step. The print comes off the plate in the same green, uncured state as any other resin and needs the same UV post-cure.

Can I over-cure a miniature? Yes, and it is more common than under-curing among people who are being careful. Over-cured resin gets brittle and light-colored resins yellow. If your minis are snapping at thin points like ankles, spears, and banner poles, cut your cure time before you switch resins.

How long should I cure before painting? Cure fully, then let the mini sit for an hour or so before priming. Fully cured resin takes primer and paint without issue. Anything still slightly tacky will fight the primer and leave you with a finish that never quite hardens.

Is a cure station worth it over a nail lamp? For the curing alone, no. For the wash function, yes, if you print often enough that hand-washing in IPA has become the thing you dread. That is the real purchase decision, and framing it as a curing upgrade is how people end up disappointed with the difference.